Chase Research IOPRINT+ Print Server Instrukcja Użytkownika Pobierz pdf

Page 1

BiAdmin Program

This document describes the installation and operation of the

BiAdmin Configuration & Management program.

Requirements

This program requires:

• Windows 95 or Windows 98

• Windows NT 3.51, Windows NT 4.0

Additional Recommendations:

• Screen resolution of 800 * 600 or greater.

• If using Novell NetWare, installation of Novell’s Client 32 for Windows is

strongly recommended. This will greatly enhance the ability to BiAdmin to

work with NetWare servers.

Installation

BiAdmin can be installed by running the setup.exe program in the directory

ioprint\utils\biadmin\disk1 on the Chase Research CD-ROM.

Select Install BiAdmin from the options available, and follow the on-screen prompts

to complete the installation.

Main Screen

Start the program by using the icon created by the setup program.

When run, the program searches the network for all active IOPRINT+ Print Servers,

then lists them on screen, as shown by the example screen below.

Figure 1: BiAdmin Main Screen

1 2 3 4 5 6 ... 15 16

Podsumowanie treści

Strona 1 - BiAdmin Program

Page 1BiAdmin ProgramThis document describes the installation and operation of theBiAdmin Configuration & Management program.RequirementsThis prog

Strona 2 - Device List

Page 10Physical Port ConfigurationMenu equivalent: Configuration – Physical PortAfter selecting the port, you will see the following screen.Figure 11:

Strona 3 - Status Icons

Page 11Serial Port ConfigurationMenu equivalent: Configuration - Serial PortCheck your serial printer to see what settings should be used. Selecting t

Strona 4 - Figure 3: Printer Status

Page 12Click the Open button to browse for firmware upgrade files. These files have a .BINextension.Click Upgrade to send the file in the upper window

Strona 5

Page 13Menu OptionsStatus MenuDevice InfoSame as Device button.Display all the configuration and status information aboutthe selected IOPRINT+ Print S

Strona 6 - AppleTalk Configuration

Page 14Set IPAddressFor TCP/IP networks only:• If a IOPRINT+ Print Server does not appear on the mainscreen, use this option to set a Device IP Addres

Strona 7

Page 15Figure 15: Configuration ScreenDevice NameEnter a new name for the selected IOPRINT+ Print Server ifyou wish.Group NameIf a group name is enter

Strona 8 - NetBEUI Settings

Page 16Diagnostics menuPrint Test PageUse this option to print a test sheet from the selectedIOPRINT+ Print Server port. The test print out will inclu

Strona 9 - Logical Port Configuration

Page 2GroupsOn the left side of the screen is a column for Groups. Each IOPRINT+ Print Servermay be placed in a group, using the Configuration-System

Strona 10 - Physical Port Configuration

Page 3of the unlisted device in order to assign an IP Address. The Default name isshown on a sticker on the base of the device.ICONSOnce a IOPRINT+ Pr

Strona 11 - Action Icons

Page 4There are 4 icons - one for each parallel port, and one for the serial port. Non-existent ports are grayed out. Selecting an icon will result in

Strona 12

Page 5Configuration IconsTo configure a IOPRINT+ Print Server, click on it once with your mouse tohighlight it. The program will ask for password conf

Strona 13 - Menu Options

Page 6Selecting this icon will allows configuration for both TCP/IP and Internet Printing.The top section of the screen is shown below.Figure 5: TCP/I

Strona 14 - Configuration Menu

Page 7Figure 7: AppleTalk ConfigurationRefer to the AppleTalk document for details of these settings.

Strona 15

Page 8NetBEUI ConfigurationMenu equivalent: Configuration - NetBEUISelecting this icon leads to the following screen.Figure 8: NetBEUI ConfigurationNe

Strona 16 - Control Menu

Page 9SNMP ConfigurationMenu equivalent: Configuration - SNMPAfter clicking this icon, the screen will look like the following.Figure 9: SNMP Configu